Gnb Battery Sizing Program
.DEC200 SERIES INDUSTRIAL BATTERY CHARGER I&O MANUAL.Location and Installation of Charger Stacking AC Electrical Supply Branch Circuit Protection AC Voltage Connections Ground Connection DC Output Fault and Display Codes DEC200 Standard Charger Operation Charger Functional Description 10.1 LED Descriptions 10.2 Pause Push Button 10.3 Smart Start Stage 10.4.DEC200 SERIES INDUSTRIAL BATTERY CHARGERS 1. IMPORTANT OPERATING AND SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS a) Before using the battery charger, read all the instructions in addition to the CAUTION, WARNING, and DANGER markings on the charger, battery, and all the associated equipment.Before installing, check that the charger nameplate data corresponds to the packing slip and to the model specified on the original sales order. The DEC200 chargers are delivered on skids for easy handling using a forklift truck.b) Remove the bolts from the top cover of the base unit, but do not discard these, as they will be required to fix the two units together. C) Use an appropriate lifting sling to lift the second unit on to the base unit, inch the second unit over the base unit and align the holes before resting the second unit on top.6. AC ELECTRICAL SUPPLY The charger must be connected to either a single phase or three phase, 60 Hertz (± 2%) AC power source. Three phase chargers cannot be powered with a single phase source.
The following transformer options are available: TABLE 1 –.FIGURE 1: SINGLE PHASE INPUT WARNING: IMPROPER WIRE AND JUMPER CONNECTION MAY CAUSE SEVERE DAMAGE TO THE CHARGER AND BATTERY NOTE: Live connection ‘L’ Must be connected to the breaker. The mains input are the only user configurable connections. PCB connections must NOT be altered from factory setting.FIGURE 2: THREE-PHASE INPUT WARNING: IMPROPER WIRE AND JUMPER CONNECTION MAY CAUSE SEVERE DAMAGE TO THE CHARGER AND BATTERY NOTE: PCB connections must NOT be altered from factory setting. 208VAC 60 Hz CONFIGURATION (208/240/480V INPUT) 208 240 Mains Input (Black) (Black) (Black) 240VAC 60 Hz CONFIGURATION (208/240/480V INPUT).6.2. AC VOLTAGE CONNECTIONS To connect the input AC voltage, route the AC conduit through the knockout hole provided.
About BAE Batteries USA. BAE Batteries USA serves the growing backup power requirements of our North American based customers. Headquartered in Somerset WI near Minneapolis/St. Paul, BAE Batteries USA provides a full line of stationary VLA and VRLA products in addition to micro-processor based battery chargers. Reference Guides: The reference guides in this section will give you a quick way to find new products from older retired models that no longer exist. The Power Battery Guide will help to select the correct C&D product model replacement for previous Power Battery models that are no longer available. Exide Corporation (formerly GNB Battery Technologies, Inc.) – Final Stipulation and Order 2014 – November 2014 Proposed Stipulation and Order, Exide Technologies, Vernon, Calif. – November 2014 Memorandum of Understanding – Department of Toxic Substances Control – November 2014.
Continue the AC wiring to the breaker terminals L1 (N) and L2 (L) (single phase input) or L1, L2, and L3 (three phase input). For proper connection, torque the screws to approximately 25 inch-pounds.9. DEC200 STANDARD CHARGER OPERATION CHARGE CONDITION CHARGING TERMINATION TERMINATION/ FAULT CODE SETTING EQUALISE EQUALISE CHARGE AUTO BALANCE Lobt CHARGE PERIOD Lobt OFF PERIOD CRITICAL FAULT CODE NONE CRITICAL FAULT CODE = Output current = Fault code, display will alternate with the two codes = Phase of charge i.e.10. CHARGER FUNCTIONAL DESCRIPTION 10.1. LED Descriptions Yellow Flashing Yellow Solid Green Solid 10.2. PAUSE PUSH BUTTON This PAUSE push button will halt the charge cycle. The battery can then be safely unplugged for up to 10 minutes.
Car Battery Sizing Chart
Gnb Battery Sizing Program Reviews
If the battery is still connected after this time, the charger will continue with the present charge cycle.10.6 EQUALIZE PUSHBUTTON Equalize charge can be enabled/disabled, when the FUNCTION button is depressed 5 second at anytime whilst a battery is connected. Only one equalize charge per recharge cycle is permitted.
Gnb Battery Website
CAUTION: DO NOT EQUALIZE MORE OFTEN THAN REQUIRED BY THE CONDITION OF THE BATTERY, AS SPECIFIED IN THE BATTERY MAINTENANCE INSTRUCTIONS.11 MAINTENANCE The charger requires minimum maintenance. ENSURE THE CHASSIS IS SECURELY GROUNDED per the local/federal Electrical Code. Do not allow excessive dust to accumulate on the components inside. Blow out with clean compressed air when necessary.